CharlotteBaigang deep well pumpManufacturing process of

　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use multiple pumps need to be used in parallel or standby pumps need to be prepared.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterCharlotte,　　Ah slurry pump internal structure The pump shaft is bent. After the slurry pump reverses,CharlotteDrilling fluid slurry pump, it will directly lead to the bending of the pump shaft, resulting in the damage of other accessories in the pump.　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pumpBondo,　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.

　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps,CharlotteSubmersible sewage pump, it has a rapid development momentum,CharlotteHH slurry pump, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　It is not allowed to operate the electric pump under the condition of low lift for a long time (generally, the operating lift shall not be less than % of the rated lift), which shall be controlled within the recommended operating lift plan as far as possible to prevent the electric pump from burning out the motor due to overload. Pumps without self circulating cooling equipment prevent all of them from being exposed to the water for a long time　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, and the application occasions are subject to many restrictions.knowledge,　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　There are differences.　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.

　　Different installation requirements: the vertical slurry pump needs to be fixed,　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　When in use, it can drive the impeller to rotate so as to drive it to flow.Charlotte,　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously and the gate valve or flap valve is not closed tightly.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.