ConcepcionSpecification and size of galvanized flat pipeSimple assembly design

QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-,ConcepcionHot dip galvanized steel pipe, etc.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Concepcion,Low alloy steel is divided into q Mn, Q St-, etc.At this time, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Moncton,Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.

The inspection items, sampling quantity, sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Shot blasting is commonly used to clean the surface of castings or strengthen the surface of square tubes.Pull square tube:Highly recommended,Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointAccording to metallographic classification the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).

Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )equipment maintenance ,Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?The normal process flow is as follows: the round steel is perforated to form a tube embryo, then pickling is carried out, the black skin on the outer surface is washed off, and then grinding is carried out. After passing the inspection, the rolling mill or cold drawing and cold drawing are carried out. Annealing is required for wall reduction, but not for air drawing. After forming, annealing and straightening are carried out, and pickling is tested and stored in the warehouse. Basically, these are the processes. Better manufacturers will perform whitening treatment during annealing to make the surface treatment more beautiful. The narrow blank of square pipe can produce welded pipe with larger diameter, and the blank of the same width can also produce welded pipe with different diameter. However, compared with the straight seam square pipe with the same length, the weld length increases by %, and the production speed is low. Square pipes with large or thick diameter are usually made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be directly welded with steel strip. Then after simple polishing, wire drawing is OK. Therefore straight seam welding is mostly used for relatively welded pipes, and spiral welding is mostly used for large-diameter welded pipes.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Concepcion,Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust, agent and similar organic matter,ConcepcionGalvanized square pipe 100x100, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.For improper stamping direction,ConcepcionSeamless galvanized square pipe, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests the bending is compacted, and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.