KanasSpecification of galvanized square pipeMarket demand is expected to improve

Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Kanas,After the square tube is cut into a single square tube, the head and root of each batch of square tube shall be subject to strict first inspection. The mechanical properties, fusion condition, surface quality of square tube and NDT shall be carried out to ensure that the pipe making process is qualified before it can be officially put into production.The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.Aumba,Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.

Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.One of the steps that are prone to defects in the production of square tubes is heat treatment and the other is tensile treatment. Today we need to know the latter. Maybe some people will have a lot of questions about why square tubes are prone to defects in tensile. Now let's analyze the specific causes of defects.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, salt etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.Customer first,For structure: as pile driving pipe and bridge; pipe for wharf, road and building structure, marine pile driving pipe, etc.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However,KanasRectangular square tube, compared with straight seam pipe of the same length, the weld length is increased by ~,KanasPunched square tube, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used,KanasSpecification for PVC and galvanized pipes, the thickness is significantly lower than the standard.

Square tube, modified square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.Welcome calls ,Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.Therefore, the plasticity and quality of qb square tube forged are relatively good, so general manufacturers will forge qb square tube, professional square tube, rectangular tube, seamless square tube, galvanized square tube, galvanized tube to ensure quality, service and quality. Your satisfaction is our pursuit! Welcome to inquire. So now there are many applications of qb square tube.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Kanas,The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).