Salvarend higaiLong shaft submerged slurry pumpAchieve the effect of unmanned operation

　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Salvarend higai,　　Microcomputer controller LW light: cause: the light is on and the machine stops, the water level is low, the water level returns to normal and the machine starts automatically.　　What is the cause of pump overload.Haskovo,　　It is occasionally found that there is insufficient liquid supply when using so what are the reasons for this situation and how to deal with it.　　Under the action of auxiliary devices,Salvarend higaiVertical heavy-duty slurry pump, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.

　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, high automation and performance　　 If the deep well pump is not used continuously after running in the well,Salvarend higaiZD slurry pump, it should be started up once a week and run for - minutes to prevent the electric pump from being started due to corrosion.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeFinance Department,　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　There are differences.

　　Moreover because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willRecommendation and consultation,　　Extend service life. In fact, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　Determine whether repair and replacement is required according to the wear condition of the ring; Check the insulation of the motor stator to see if there is any trace of chamber sweeping damage; Check whether there is sand deposition and sewage blockage at the pump bottom, whether there is sand deposition at the pool bottom, and whether it is necessary to cut off water and clear silt.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submergedSalvarend higai,　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.