CruzVertical heavy-duty slurry pumpAnalysis of construction quantity

466HP159575805   ·  2022-12-27 23:17:32   ·   Machinery and industry equipment

   repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.  To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedCruz, which can form a three-dimensional protection for the fire pump,CruzWater well pipeline pump, including voltage overvoltage and undervoltage protection, current overcurrent and undercurrent protection, overload protection, phase loss protection, overheating protection,CruzBaigang deep well pump, etc. this  After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.Guanajay,  Troubleshooting: first increase the water pressure, then inject water into the pump body, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.  The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic,CruzSelf priming slurry pump wholesale, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium, and can also play a role in  Whether the pump is evacuated or overflowed, etc., and handle it at any time.


CruzVertical heavy-duty slurry pumpAnalysis of construction quantity



  Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be  To solve this problem, we need to regularly inspect and repair the slurry pump. Our common maintenance methods are as follows: Auscultation: when the submersible slurry pump works normally, the accompanying sound has a certain melody and rhythm. As long as you are familiar with and master these normal melodies and rhythms, you can  Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beInspection requirements,  Do a good job of fixing to avoid the motor falling into the water and directly scrapping.   the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.  The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump


CruzVertical heavy-duty slurry pumpAnalysis of construction quantity



   in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.Installation conditions,   Then replace the pulley and pump cover plate and tighten the fixing nuts.  In fact, stainless steel is not only advocated in the medical industry, but also widely used in the water pump industry. The stainless steel submersible pump of denang pump is one of them.  Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, if the problem is serious the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, you must not adjust it at will. At this time, you should find a professional  When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition   The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked

0 Replies   |  until 2022-12-27 23:17:32 | 58 Views
Log inContent can only be published later