PabiannisHydraulic lifting platform Electric lifting platformTo make the service tangible

Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.Pabiannis,Check valve leakage, oil pipe check valve leakage. The solution is to carefully check whether the one-way valve is functioning properly. If it is not normal, it is recommended to replace the one-way valve with a new one.The combined platform is often used in small workshops with small volume of goods. However,. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve it inevitably increases the distance of handling tools/vehicles in the workshop.Manjacaze, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. In order to ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve and balance circuit are installed on the return oil circuit to maintain pressure and ensure that the descent speed is not affected by changes in heavy objects. The throttle valve regulates the flow rate and the lifting speed. To ensure safe and reliable braking and prevent accidents a hydraulic one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking when the hydraulic pipeline bursts. Install an overload sound alarm to distinguish between overload or equipment failure.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to % of the maximum load capacity. After lifting times, each load-bearing component must not have deformation or cracks.

Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes,PabiannisMechanical hydraulic lifting platform, and should not be placed randomly to prevent accidents caused by falling from a height.Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.Customer first,Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, which has been favored by many users.

Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to % of the maximum load capacity. After lifting times, each load-bearing component must not have deformation or cracks.Promotion,Pabiannis6-meter hydraulic lifting platform,Ensure that there is a suitable power supply at the installation site, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature, the volume will change, which is reflected in the lowering of the position on the table.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range,PabiannisHydraulic guide rail type lifting platform, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.Pabiannis,Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site