Production mode stainless steel pipe can be divided into seamless pipe and welded pipe according to the production mode. Seamless steel pipe can be divided into hot-rolled pipe, cold drawn pipe and pipe. Cold drawing and cold rolling are the secondary processing of steel pipe; Welded pipe is divided into straight seam welded pipe and spiral welded pipe.When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.Sancti-Spiritus,h chemical composition carbon C: Manganese Mn: silicon Si: chromium Cr: nickel Ni: phosphorus P: sulfur s: niobium NB: h stainless steel Name: austenitic stainless steel standard: aisastm model: huns No.: Note: a single value is a high value unless otherwise indicated; when used in some pipe making processes, the nickel content of some models of austenitic stainless steel must be slightly higher than that shown in the table; optional High TA content is .%; high content is .%; high content is the basic characteristics of stainless steel with high temperature strength and high temperature plasticity, excellent oxidation resistance and corrosion resistance, good structural stability, uniform chemical composition, good processing performance and welding performance, high dimensional accuracy and surface quality. causes of rust when brown spots appear on the surface of stainless steel They were greatly surprised: & rdquo; stainless steel will not rust. Rust is not stainless steel. There may be something wrong with the steel quality. & rdquo; in fact, this is a one-sided wrong view of the lack of understanding of stainless steel. Stainless steel will also rust under certain conditionsChloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough,Sancti-Spiritus9Cr18 stainless steel plate, the container leaks due to corrosion days after it is replaced with stainless steel.Ho, clock spring and steel wire rope in aviation structure after deformation strengthening. If welding is required after deformation, spot welding process and deformation can only be used to increase the tendency of stress corrosionProduction process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).Austenitic stainless steel can be used to manufacture stainless spring, clock spring and steel wire rope in aviation structure after deformation strengthening. If welding is required after deformation, spot welding process and deformation can only be used to increase the tendency of stress corrosion
When the stainless steel pipe with solid core welding wire is prefabricated, and the ventilation is very easy. At this time, the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), and the outside is blocked with adhesive cloth.In polluted air (such as atmosphere containing a large amount of sulfide, carbon oxide and nitrogen oxide), acetic acid liquid points will be formed,Sancti-SpiritusSus631 stainless steel plate, which will lead to chemical corrosion.After that, the second widely used steel is mainly used in food industry, it is also used as & ldquo; marine steel & rdquo;. SS is usually used in nuclear fuel recovery devices. Grade stainless steel Steel pipes usually also meet this application level.details,Stainless steel pipes are divided into ordinary carbon steel pipes, high-quality carbon structural steel pipes, alloy structural pipes, alloy steel pipes, bearing steel pipes, stainless steel pipes, bimetallic composite pipes, coated and coated pipes to save precious metals and meet special requirements. Stainless steel pipes have a wide variety, different uses, different technical requirements and different production. The outer diameter range of steel pipe currently produced is . & mdash; mm, wall thickness range . ~ mm. In order to distinguish its characteristics, we specialize in providing quality assurance for L stainless steel pipe, s stainless steel pipe and L stainless steel pipe. During the preferential activities, new and old customers are welcome to consult. Steel pipes are usually classified according to the following.When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .The petrochemical industry including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc., with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes, etc.
There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification,Sancti-SpiritusHow many stainless steel plates, collision with other components, purification and damage of iron metal.Quality assurance,Deburring: after the pipe is cut off, the burr shall be removed to avoid cutting the sealing ring.Basic weight (density) / kg of steel plate: SPCC & mdash& mdash; Cold rolled carbon steel sheet and strip are generally used, which is equivalent to qa. The third letter C is the abbreviation of cold. When it is necessary to ensure the tensile test, add t at the end of the brand as spcct.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).Sancti-Spiritus,Model & mdash; Add a small amount of sulfur and phosphorus to make it easier to cut.The welding of stainless steel pipe is usually composed of backing welding, filling welding and cover welding. Backing welding of stainless steel pipe is a key link in stainless steel pipe welding, which is not only related to the quality of engineeringWhen improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.