KorozarPrice of galvanized square pipe 40What are the specific installation steps

256HP158312377   ·  2023-05-04 06:12:10   ·   Building materials

When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)Korozar,The welding sequence is to reduce deformation. The welding sequence of rectangular butt welding shall adopt layered and symmetrical skip welding from the middle to both sides according to the following principles. The welding deformation is smaller than that of straight through welding, which is conducive to the dispersion and release of stress and avoid complex stress in weldments. During straight through welding, due to continuous welding, the heat input is large, the heating area is large, and the plastic deformation area caused by compression is large, so the shrinkage deformation after welding is very large. In case of layered and segmented skip welding, the section of each layer is very small, and each layer is divided into several sections for skip welding. Each welding section basically re establishes the secondary temperature field on the cold steel plate, and a narrow plastic deformation zone appears each time. Therefore, the average width of the plastic deformation zone (i.e. the size of transverse shrinkage) is smaller than that of the corresponding layered straight through welding, and the longitudinal shrinkage is also smaller, The welding deformation is smaller than that of continuous filling.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, that is the warehouse with roof, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days enclosure, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ~O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodAffery,Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.The disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.


KorozarPrice of galvanized square pipe 40What are the specific installation steps



The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeBefore gas cutting, remove the dirt and grease on the steel surface, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be ~ mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.For more,KorozarRectangular square tube, please check,Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing sedimentation pipe, etc.Generally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.


KorozarPrice of galvanized square pipe 40What are the specific installation steps



Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation,Korozar150 hot dip galvanized pipe, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Customer first,Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, the appropriate thinning coefficient & psi is selected; N (generally .t ~ .t), if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Korozar,Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.The strength, many machine parts work under cyclic load, under which fatigue will occur.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.

5 Replies   |  until 2023-05-04 06:12:10 | 152 Views

Meibo Children's Toys Company 2023-05-04 08:19:37 support  0 | be opposed to  0

Can you give me KorozarPrice of galvanized square pipe 40 detailed specification data?

Jingcheng Information Technology Co., Ltd. 2023-05-04 07:42:56 support  0 | be opposed to  0

I bought a lot of you KorozarPrice of galvanized square pipe 40 and I am very satisfied. Very good seller, I will come often.

sale of flowers 2023-05-04 07:36:16 support  0 | be opposed to  0

This store is really good, with good quality and low price, the owner is very generous, and the customer service is also very patient. I don’t understand this KorozarPrice of galvanized square pipe 40. They explain to me patiently. It is really the conscience of the industry. I want to recommend this shop to my friends and let them all come to this shop to buy clothes!

Landscaping Engineering Services 2023-05-04 07:30:25 support  0 | be opposed to  0

A good seller, even a novice, a lot of KorozarPrice of galvanized square pipe 40 don’t understand. Fortunately, the seller has patient guidance on the other end of the computer, and I have a sense of accomplishment, and finally figured out the problem that I didn’t understand.^- ^Learn more in the future!

metal fasteners 2023-05-04 13:37:11 support  0 | be opposed to  0

It's worthy of praise, really good, KorozarPrice of galvanized square pipe 40 I like it very much.
Log inContent can only be published later