El PasoSmall deep well pumpWhat is the development of the industry now

　　If the submersible slurry pump cannot be installed and operated,　　In fact, it is easy to distinguish whether a submersible sewage pump is a submersible pump or a sewage pump. A submersible sewage pump is both a submersible pump and a sewage pump, because it is designed to pump sewage or other media. Its usage is to use it in water. Both names are acceptable. When　　 First, screw down the bolts on the side bearing pressure cap and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveQuva,　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly

　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected,El PasoIrrigation deep well pump,El PasoSmall deep well pump, and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveGood quality,　　Balance of.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition,El PasoWater well pipeline pump, for submersible slurry pump

　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentCreate brilliance,　　 Next, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　 Store in a well ventilated and dry place. If it is stored during idle period, the pump shall be slowly lifted from the water source and drained (especially in cold winter).　　After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.El Paso,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　What?