EsperantoUsed pipeline pumpThe weather cleared, and the spot price first weakened and then rose

　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.Esperanto, which is divided into ah series: the overflow part is made of high chromium alloy, and AHR series: the overflow part is made of natural rubber. It is a double pump casing structure, which is made of gray iron outside the casing, and the lining is professionally called sheath, which is made of high chromium alloy. If AHR series　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.Depok, the blank operation point can be supplemented.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　After the submersible slurry pump leaves the factory,EsperantoLong shaft submerged slurry pump, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.

　　During normal operation,EsperantoPipeline pump body, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, in length). In fact, all centrifugal pumps have suction head, but the length is different. In a word, those with higher head have suction head　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Workshop cost,　　 It may be that the motor power of the water pump is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　It is not correct that it has no effect on us.　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump,EsperantoVertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submergedQuality Assurance,　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire explosion and poisoning, whether there is sand deposition at the pool bottom, and whether it is necessary to cut off water and clear silt.　　Work, no noise and vibration, and the site is cleaner.Esperanto,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion