KomitanchiloAh slurry pumpHow to realize mass consumption

　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpKomitanchilo,　　The impeller channel reaches the outer edge.　　It is not correct that it has no effect on us.Comayagua,　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which can offset part of the axial force and prolong the service life of the bearing.

　　Troubleshooting: first increase the water pressure, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　In recent years, domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation,KomitanchiloZD slurry pump, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speedquality　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　Is called cavitation phenomenon.

　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areasnew product,　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, in length). In fact, all centrifugal pumps have suction head, but the length is different. In a word, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beKomitanchilo,　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue,KomitanchiloWater well pipeline pump, industrial cooling, farmland irrigation seawater lifting, ship load adjustment,KomitanchiloLong shaft submerged slurry pump, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　The whole packing body, including the packing gland, packing ring and packing needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane