TijuanaThick galvanized square pipeOn the absorption of rays

The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.Tijuana,It must be noted that in the overall process of square tube coating process, the cost of surface treatment is still relatively high, so it is very important to select appropriate treatment. Only by selecting the right treatment can the coating quality of square pipe be well guaranteed.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.Busia,. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate,TijuanaWelded galvanized pipe, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, in order to make the front end of the square tube pass through the die hole smoothly, so that the clamp jaw of the drawing trolley can the head of the square tube, it is necessary to sharpen the head of the square tube before drawing. Therefore, the end of the square tube with a fixed length should be heated in the slit heating furnace, It is generally ~ mm, and the heating temperature is between ~ ℃ according to different wall thickness. Then use ~ kg air hammer to sharpen and grind the head of the square pipe. Generally, the square pipe with diameter less than mm can be sharpened by rotary forging hammer or roll forging machine.Square tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes, large smoke tubes, small smoke tubes and arch brick tubes for locomotive boilers. Square tubes for high-pressure boilers (gb- is a high-quality carbon steel, alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.Work courses,Ferrous metals refer to iron and iron alloys. Such as steel, pig iron, cast iron, etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, collectively referred to as iron carbon alloy.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.

Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Safety production,Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.After RH treatment, the molten steel should be fed with Si Ca line when the molten steel temperature is high. At this time,Tijuana4x6 square tube, calcium treatment can reduce sulfur segregation in the later solidification process.Derusting grade for the construction process of epoxy, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.Tijuana,In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes decorative square tubes, mechanical square tubes building square tubes, etc. according to their uses.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.