HoustonAh slurry pumpPrinciple of direction

　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　It is an auxiliary means for some on-site monitoring.Houston,　　Consider the vertical separation level of the tail equipment. The water pump control cabinet has a variety of protection s and complete status display, such as overload, short circuit,HoustonVertical heavy-duty slurry pump, phase loss protection, pump body water leakage, motor over temperature and electric leakage, as well as single pump and multi pump control working modes, a variety of main and standby pump switching modes and various　　The of descending axial force can be used for slurry transportation in power plants,HoustonSelf priming slurry pump wholesale, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Sakete,　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core grind it to the oxide layer on the wire core, wrap the insulation layer and sheath layer wipe the wire core with alcohol (or hydrochloric acid), and dry it naturally.　　The high-efficiency slurry pump has three characteristics: first, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　 Change the oil: if the oil contains water, drain it, change the oil, seal the gasket, and then tighten the screw plug.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Inspection standard,　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　 Then reinstall the equipment on the engine and install the rubber hose.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,

　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Inspection standard,　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　 Check the surrounding environment: when the ambient temperature is higher than ℃,HoustonLong shaft submerged slurry pump, the temperature of the air inlet will rise, resulting in overheating of the motor. Try to improve the working environment. Such as setting up shade sheds for shading.　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.Houston, it can transport the slurry and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life