Ginotepe15cr1mov alloy pipeAnalysis of incentive requirements

Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.Ginotepe,Because of this characteristic, seamless pipe is widely used in oil transportation, natural gas, natural gas, water and some solid materials transportation. Smooth steel pipe has strong bending advantages compared with other steel pipes. And the smooth steel pipe is also light in weight. It is a very economical single-sided steel.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Acacias,The finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃The core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power and the power is large, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.

I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide,Ginotepe16Mn seamless pipe factory, medium and narrow flange I-beams. The specifications of the first two are -, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards. Pipe installation:After determining the reasonable pickling agent and polishing solution,GinotepePrice of 16 cm I-beam, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Workshop cost,H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for setting→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:

The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.market,I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure. After chromate passivation, the zinc coating forms white, colorful and military green, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Ginotepe, Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted,GinotepeHow much is 16# I-beam, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole etc.c. quality inspection is carried out for alloy pipes, so that the whole process of steel pipe processing is under reasonable inspection and supervision, and the product quality is reasonably guaranteed.Key technical characteristics of alloy pipe