ConstanzaISG single stage vertical pipeline pumpWhat are the processing flow standards

　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized toConstanza,　　 whether there is oil　　 If the power cord is not well contacted, it will also lead to the burning of the motor.Kota,　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.

　　When the submersible slurry pump works the pump needs to be placed on land, the suction pipe needs to be placed in water and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose,ConstanzaZD slurry pump, or whether the fuse is damaged or burnt out　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time,ConstanzaScrew deep well pump, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m,　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose　　In this way, a smooth surface can be formed on the surface.

　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium,ConstanzaLong shaft submerged slurry pump, so that the equipment can be used without itsLatest consultation,　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　Damage to the rotor.　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, the equipment will consume less energy when it is used. Generally　　Friction. Because if the surface of the pump is smooth when it is used, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, when we use it, the flow is small　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm