JalapaPipeline pump bodyProfessional road

　　During normal operation, the temperature of the motor is very high,JalapaCorrosive pipeline pump, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　 Ensure that the electric pump operates normally The electric pump needs to be equipped with a fully active water pump control cabinet when there are no other conditions. Do not directly connect the power grid or use a knife switch to connect the power supply.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.boston,　　The direction of the differential pressure force is opposite,JalapaSplit vertical pipeline pump, which can offset part of the axial force and prolong the service life of the bearing.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.

　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.　　 No maintenance: if it is not used continuously after startup, the submersible pump will rust and cannot be started. If it is not used for a long time, do not immerse it in water for a long time. Put it into clean water and run it for a few minutes to clean the mud inside and outside the pump.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Work courses,　　About %), and motor power p=i × U indicates that high power and current will increase.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.

　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.Inspection environment,　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　 With protection . cf fire control cabinet integrates many electrical components, which can form a three-dimensional protection for the fire pump, including voltage overvoltage and undervoltage protection, current overcurrent and undercurrent protection, overload protection, phase loss protection overheating protection, etc. this　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.Jalapa,JalapaWater well pipeline pump,　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.