Victoria de Las TunasVertical slurry pumpApplication process

466HP159575805   ·  2023-01-22 00:13:56   ·   Machinery and industry equipment

  How to avoid this situation when the equipment is in use.   Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.Victoria de Las Tunas,  Work to prevent the electric pump from overheating and damage. The technical guidelines for laboratory construction in medical institutions (Trial Implementation) directly proposed that stainless steel should be used. Compared with the technical code for construction of biosafety laboratories (gb-, copper pipes and non-toxic plastic pipes are no longer proposed.  The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Lukuledi,  Rate.  Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as  It is also necessary to clean the ventilation duct to avoid blockage.


Victoria de Las TunasVertical slurry pumpApplication process



  Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed,Victoria de Las TunasSmall deep well pump, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power  For /g-g gravel pump,Victoria de Las TunasDouble suction slurry pump, which belongs to large-diameter slurry pump, it is necessary to remove the impeller removal ring and rotate the impeller in the opposite direction.  Extend service life. In fact the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump which can separate the pump body from the motor,  Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump  Commodity.   there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainly


Victoria de Las TunasVertical slurry pumpApplication process



  The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentTest results,  At present, mechanical seals occupy an increasing share in the slurry pump seal market.  The horizontal slurry pump is a cantilever centrifugal slurry pump, which is suitable for conveying abrasive or corrosive slurry. The structures of all types of horizontal slurry pumps are similar except that the pump head (including pump body,Victoria de Las TunasISG single stage vertical pipeline pump, pump cover, etc.) has different structures. The pump head part, shaft seal part and transmission part  The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome,  Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be  Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.   The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.

4 Replies   |  until 2023-01-22 00:13:56 | 139 Views

linkage door 2023-01-22 08:14:55 support  0 | be opposed to  0

Victoria de Las TunasVertical slurry pump How much is the minimum, can it be wholesale

Production and sales of wall and floor tiles of electrostatic plastic powder 2023-01-22 07:48:09 support  0 | be opposed to  0

Victoria de Las TunasVertical slurry pump The quality is not bad, and the goods are delivered in time. I recommend you to buy it next time.

FRP digester 2023-01-22 07:20:48 support  0 | be opposed to  0

Victoria de Las TunasVertical slurry pump Not bad, the price is worth it, just right.

Mechanical and electrical equipment 2023-01-22 08:56:18 support  0 | be opposed to  0

Your company Victoria de Las TunasVertical slurry pump has a very good service attitude, thank you, and like you.
Log inContent can only be published later