St. Louis NorthCustom welded pipe manufacturerHigh degree of finished product

Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, the combination of more than two systems. For example, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole etc.The finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length, wear resistance and maximum temperature of ℃St. Louis North,Wire sleeve: it is also a general carbon steel welded steel pipe. It is used in concrete and various structural power distribution projects. The commonly used nominal diameter is from -mm. The wall of wire sleeve is thin, which is mostly used after coating or galvanizing, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Su-ngai Kolok,The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.The flange of H-beam is of equal thickness,St. Louis NorthHow much is a meter of 4-inch galvanized pipe, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, vehicle manufacturing, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.

Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush. When the end span plate is connected with the concrete beam for structural reinforcement,St. Louis NorthHow much is the I-beam now, the length of the surface mesh reinforcement extending into the beam shall not be less than d. When the beam width is small, the extended reinforcement shall be bent . When the perimeter of the floor is poured integrally with the concrete beam or wall, the length of the surface mesh reinforcement extending into the beam shall not be less than the anchorage length of the small reinforcement required by the standard (without transverse reinforcement), when the beam width is small, the extended reinforcement shall be bent.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)wholesaler,Passivation treatment operation of alloy pipeWhether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.According to the theory of steel structure, the I-beam flange should be stressed, that is, the I-beam should be standing rather than lying down.

At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications,St. Louis North1Cr5Mo thick wall alloy pipe, dimensions and relevant standards.Inspection items,Introduction to product knowledge of alloy pipe:They are not affected by surrounding factors and processes, including corrosion.After isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.St. Louis North,Requirements of alloy tubes for low and medium pressure boilersWhat are the requirements for alloy pipe construction accessoriesI-beam is widely used