Shangri la townLong shaft submerged slurry pumpHow to effectively remove impurities in

　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.Shangri la town,　　The resistance loss in the lifting pipe and the resistance loss of the water delivery pipe after the outlet of the pump base.　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.Rodriguez,　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　 Constantly observe the instrument, check the electrical equipment, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.Excellent quality,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber,Shangri la townPipeline pump, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, which can separate the pump body from the motor, so it mainly plays a role in use　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pumpService first,　　If there are sundries blocked,Shangri la townQJ submersible pump, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging it needs to be replaced in time,　　Water pump control cabinet Time control: the chassis panel is equipped with a time setting button and a display. The user can control the opening and closing of the water pump according to the timing needs. It is suitable for the control of various timed or regular intermittent working modes.　　It is occasionally found that there is insufficient liquid supply when using,　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator outside micrometer, feeler gauge, screwdriver with handle copper bar, hammer, V-shaped irons of the same specification, clean kerosene, oil basin,Shangri la townZD slurry pump, cotton yarn, etc.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged