Mannheim15 galvanized square pipeHigh precision
The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.The strength, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Mannheim,Polishing process of square tube square tube is widely used in our life, so in the subsequent application process, the requirements for square tube in many places are also quite strict, especially for surface treatment. Today, we briefly introduce how the polishing process should be carried out.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle,When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition,MannheimThick wall galvanized square pipe factory, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed), the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.
Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade,MannheimSquare tube weight, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, remove the dirt and grease on the steel surface, and leave a certain space below to facilitate the blowing out of slag. During gas cutting, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be ~ mm away from the tip of the flame core. If the distance is too close the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.The inspection items, sampling quantity sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Development Curriculum, oil, gas and other fluids.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodBecause the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.
Ferrous metals refer to iron and iron alloys. Such as steel, pig iron, ferroalloy, cast iron etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, collectively referred to as iron carbon alloy.Product range,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, and then cut into the required length. Stage ( & mdash; )The common surface treatment of square pipe includes surface treatment, chemical treatment, shot blasting treatment, manual mechanical treatment and flame treatment. The treated will be separated. ~ Mpa compressed air entrains abrasives, and the nozzle sprays to the steel surface at high speed. The impact and friction of abrasives remove the oxide scale, and make the steel surface reach a certain roughness.Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.Mannheim,The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.