PeramaHow much is the price of q355b I-beam per tonWhat is the hazard of gloss
When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web,Perama15cr1mov alloy pipe, it is divided into wide, medium and narrow flange I-beams.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties weldability and structural size of I-beam.Perama, Product description of galvanized pipeStages needing attention in the production and manufacture of alloy tubesIngolstadt,Alloy pipes can be used for heating (cooling) projects.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.
H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete which is convenient for settingCheck whether the manufacturer&#;s qualification, business license, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, investigate the supplier&#;s performance and the projects served in the past. Whether there is a self built logistics fleet or not, choosing a service provider with a self built logistics fleet can reduce the transportation cost, and more importantly, ensure the timeliness of delivery. After sales service,PeramaWhich is a good welded pipe manufacturer, whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe, the surface is smooth and flat, the weld is dense, without burr, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, bend the welded pipe for degrees, and there is no crack at the bend.I-beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Good reputation,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.C - section steel is reliable and stable in stress, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityThe finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length,PeramaHow much is a 25mm galvanized pipe, wear resistance and maximum temperature of ℃
Frame line crackHonest service, and the power is large, generally about KW, and PLC control is mostly used.Perama,Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Requirements of alloy tubes for low and medium pressure boilersDue to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.