AbquikiWQ submersible pump parametersCorrect maintenance, you know

　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pumpAbquiki,AbquikiDeep well pump,　　Select an appropriate flow according to the water inflow of the well or pool or the water consumption required by the actual engineering system. During model selection, the flow shall be close to the model flow grade of the sample (to ensure that the pump operates in the high efficiency zone).　　 It may be that the motor power of the water pump is too large,AbquikiAh slurry pump, the working current is too large, and the heat generation is too large,AbquikiQuotation slurry pump, resulting in the high temperature of the vacuum pump.Leiah,　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　 for screws that are too tight or rusted for a long time, keep a small amount of cleaning water flowing along the shaft or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.

　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　 transmission device type (gearbox transmission, flat belt transmission, V-belt transmission)　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.reform,　　 Inspection before installation: Check the specification, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.

　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pumpProduct range,　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　Huanya pump - long shaft deep well pump　　About %), and motor power p=i × U indicates that high power and current will increase.Abquiki,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.