ColumbusSubmersible sewage pumpDetailed explanation of type and working principle

　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged,ColumbusAh slurry pump, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.Columbus,　　The structural characteristics are described respectively.　　It is also necessary to clean the ventilation duct to avoid blockage.Snina,　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　Therefore, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　The industry is facing new technological innovations. Enterprises have also launched their own killer maces in the competition, constantly improving their R & D teams and studying the related core production technologies, so as to improve the competitiveness of enterprises in the market.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,investment,　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　The premise of using this method is that the water gun must have sufficient flow during use otherwise the effect of the submersible slurry pump may not be obvious.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.

　　During adjustment, firstly loosen the support cover, then compress the nut,ColumbusSubmersible sewage pump, and then loosen the bearing seat. After adjusting the screw tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationconsumption,　　Adjustment. When using the submersible slurry pump, which will cause equipment problems and affect work efficiency. So we&#;re using　　Self priming refers to the process of sucking water from low to the pump cavity when there is no water (empty pipe) in the inlet pipeline (verb, self priming is an action and a process). Only the self-priming pump can have the self-priming .　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.Columbus, packing ring and packing including the packing gland, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However,ColumbusUsed pipeline pump, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal