Corralillo310S stainless steel plateProduct quality plan requirements
The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength,CorralilloStainless steel handrail pipe, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform, it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), American code (ACI -) and Japanese code (aij-cft), China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, prepare construction scheme and construction schedule scheme, and establish quality standards.Model & mdash; Add a small amount of sulfur and phosphorus to make it easier to cut.Corralillo,Mechanical machinability in high-speed machine, the feed rate and cutting speed of alloy are the same as L. If carbonization is adopted, the cutting speed is reduced by about % compared with L. the performance of machinery and equipment and their components plays a key role here. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.Polonnaruwa,Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die and the jaw is perpendicular to the pipe axis.Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.
Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.Stainless steel has the ability of atmospheric oxidation, that is, it does not rust. At the same time, it also has the ability of corrosion resistance in the medium containing acid, alkali and salt, that is, corrosion resistance. However, its corrosion resistance changes with its own chemical composition, mutual state, service conditions and environmental medium type. For example, in the sea fog with a lot of salt it will soon rust, while stainless steel performs well. Therefore, not any kind of stainless steel can resist corrosion and rust at any timeModel & mdash; Commonly used precipitation hardening stainless steel model usually also called -; %Cr,%Ni.Market trend,High frequency welding high frequency welding: with relatively high power supply, it can reach a higher welding speed for steel pipes with different materials, outer diameter and wall thickness. Compared with argon arc welding, it is more than ten times its high welding speed. Therefore, stainless steel pipes for common use have a higher consumption rate. Due to the high speed of high frequency welding, it is difficult to remove burrs in welded pipes. At present, high frequency welding Welded stainless steel pipe can not be borne by chemical and nuclear industries, which is also one of the reasons.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, which makes up for the disadvantage of Brinell method, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation, the hardness value is not as accurate as Brinell method.Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.
Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.Bidding,Stabilization treatment. Generally, it is used for - steel containing Ti and Nb in the solid solution treatment line. After the solid treatment, the steel is heated to ~ ℃ for heat preservation and air cooling. At this time, the carbides of Cr are completely dissolved, while the carbides of titanium removal are not completely dissolved, so that it is impossible for the carbon to form chromium carbides again. Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe ensure the quality, Guarantee service. Guarantee quality. Your satisfaction is our pursuit! Welcome to inquire. Therefore, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality for example,Corralillo20 stainless steel welded pipe, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical,Corralillo304 stainless steel pipe, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.Corralillo, Series & mdash; Martensitic precipitation hardening stainless steel.Shape stress, temperature and metal flow of forgings and dies. Results the multi-step upsetting extrusion process under high temperature can make the end of steel pipe meet the forming requirements. Conclusion the plastic forming process of steel pipe end is feasible, which has important reference significance for the improvement of pipe connection mode of railway freight car braking system.CE--“ Code for design of cold formed stainless steel structural parts & rdquo; And & ldquo; jointly published by nidi and euro inox; Structural stainless steel design manual & rdquo; The design of structural parts for buildings with long service life and good integrity has been simplified.